The Fill and Flip Microplate Loader is simple to use and much faster than adding beads, one-at-a-time, to 96-well microplate wells. Handles a variety of loading needs including both spherical and irregular shaped bead media. Providing they are pourable and dry, seeds, milled agicultural products, resins and powdered solid chemicals can also be loaded.
The Microplate Bead Loader Kit consists of a bead loading platform with spatula , two different sized s.s. frames, one 0.3 ml 'measuring' microplate and one 1 ml 'measuring' microplate.
Of the three bead loaders we offer the Suction-type 96-well, deep well Microplate Bead Loader is the fastest. Beads are loaded into 96 deep well microplates at a rate of about 10 microplates per minute. It is limited to loading spherical glass or ceramic beads only (i.e., not irregularly shaped particles or steel beads). The loader delivers a 0.4 ml load of beads to each well and is compatible with all 96-well, deep well microplates. Included is a 96-nozzle loading manifold, a hand held 110 VAC electrical suction unit and an on/off foot switch.
Hamilton Beach is the worlds largest manufacturer of commercial grade blenders. The model 909 comes with a one liter stainless steel container and can handle the toughest job required from a blade blender.
Cat. No. 909, 115 volt model
Cat. No. 909EUR, 230 volt model
This tube holder is machined out of a 1.5 lb aluminum block and has the dimensions of a standard 2ml deep well microplate. It is used with the MiniBeadbeater-96 cell disrupter. One or two 50 ml screw cap centrifuge tubes are placed completely inside the cold block and the contents shaken in the "wall to wall" direction. The block can be pre-cooled in a deep freezer or, at cryo-temperatures, with dry-ice or liquid nitrogen.
Included with each vial block are 25 sterile, polypropylene 50 ml screw cap tubes (Stockwell brand, part # 3252).*
*Important note: To maximize the efficiency of heat transfer, this aluminum tube holder was designed to fit with close tolerance to the Stockwell-brand 50 ml tube. Other brands of 50 ml centrifuge tube may not fit properly. If you prefer to use a different brand tube, please check with us for compatibility.
50ml polypropylene screw cap centrifuge tubes. Sterile, with cap. 25 tubes per bag.
The BeadBeater is the ultimate laboratory-scale homogenizer for disrupting aqueous suspensions of yeast, fungi or bacteria. Complete cell lysis of 10-80 g (wet weight) of cells is achieved in about three minutes of operation.
The BeadBeater comes complete with a 350 ml polycarbonate chamber, rotor assembly, motor base, ice-water cooling jacket, and your choice of one pound of glass beads...
Select the catalog number ending in...
-101 for 0.1 mm glass beads
-105 for 0.5 mm glass beads
-110 for 1.0 mm glass beads
Also, if the BeadBeater is to be used in countries with a 220-240 volt power supply, please select the catalog number containing "EUR."
Our BioChopper Kit provides two simple tools to aid in preparing your tissue samples for homogenation.
The BioHomogenizer is a rotor-stator type tissue homogenizer designed to rapidly homogenize, disperse, and emulsify biological samples in aqueous media from 1 to 1000 ml. The BioHomogenizer includes both the motor and probe.
Cat. No. 1281, BioHomogenizer for 1-200ml samples, complete with 1.4 cm probe
Cat. No. 1281EUR, 230 volt version of No. 1281
Cat. No. 1285, BioHomogenizer for 100-2000ml samples, complete with 2.5 cm probe
Cat. No. 1285EUR, 230 volt version of No. 1285
A low cost, versatile high-speed mixer and blender. Perfect for blade blending in open beakers, jars, and bowls. Swiss-made.
Cat. No. 10810, BioMixer, 115 volt Includes three mixing attachments, grinding mill, and plastic stand.
Cat. No. 10810EUR, BioMixer, 230 volt Includes three mixing attachments, grinding mill, and plastic stand.
The BioPulverizer quickly fragments hard frozen tissue samples into tiny pieces the size of grains of sand or course powder. The primary benefit of pulverizing pieces of tissue is to optimize subsequent rapid and complete cell lysis using lytic solutions or mechanical homogenizers. For difficult tissues such as tendon, skin, and tumors it is an essential step (read more). The BioPulverizer is also used at room temperature to fragment friable, dry biomaterial such as non-oily seeds, bone and teeth.
There are four different hand-operated BioPulverizers for quickly pulverizing 10 mg to 10 g of frozen tissue.
Cat. No. 59012N, BioPulverizer, capacity 10-100mg
Cat. No. 59013N, BioPulverizer, capacity 0.1-1g
Cat. No. 59014N, BioPulverizer, capacity 1-10g
Cat. No. 59012MS, MultiSample BioPulverizer, 12 wells, capacity 10-100mg per well*
*Twelve pestles are included with each 59012MS.
The BioRotator-6 is a fully adjustable, rotational mixer designed for a wide variety of mixing needs.
Cat. No. 792, BioRotator-6, 115 volt
Cat. No. 792EUR, BioRotator-6, 230 volt
NOTE: EACH BIOROTATOR-6 COMES WITH ONE ATTACHMENT OF YOUR CHOICE. SEE "BIOROTATOR ATTACHMENTS" BELOW TO SPECIFY.
The BioSqueezer is used to "snap-freeze" (quickly freeze) 10-100 mg of soft animal and human tissue. It does the same thing as a classic freeze clamp but is easier to use and gives more reproducable results.
Fresh tissue is compressed into a thin disc about the size of a small coin under pressure from a stainless steel clamp head that has been pre-cooled in liquid nitrogen or dry ice. Freezing occurs in a few milliseconds, thus offering a "snapshot" of metabolic events in the cells. The hard frozen disc is easily fragmented by hand or by grounding in a Cryo-Cup mortar and pestle for subsequent rapid extraction of labile nucleic acids, proteins and other intracellular products.
The BioVortexer™ is a battery-powered motor drive designed to rotate stirring rods or plastic pestles in 1.5 ml microtubes. Rotating at thousands of revolutions per minute, it makes short work of dispersing centrifugal pellets or grinding small tissue samples.
Cat. No. 1083MC, BioVortexer Stirring Kit. Includes motor, batteries and 100 - 1/8"X3" stirring rods.
Cat. No. 1083, BioVortexer, motor only. Batteries included.
Cat. No. 183, Additional BioVortexer polypropylene stirring rods, 1/8"X3" (500 count).
Cat. No. 1017MC, BioVortexer Grinding Kit. Includes motor, batteries, 100 SpiralPestles™ with matching 1.5 ml microvials and sample of SpiralPestle™ Grinding Beads.
Cat. No. 1017, Additional SpiralPestles™ with matching 1.5 ml microvials (100 count) and sample of SpiralPestle™ Grinding Beads.
The Cryo-Cup Grinder is a mortar and pestle specifically designed to pulverize and powder plant and animal tissue samples at liquid nitrogen temperatures. It gives superior results compared to conventional ceramic mortar-pestles.
Cat. No. 206, Cryo-cup Grinder, complete, includes two different size polypropylene pestle balls. See below for extra cups (mortars) and pestle balls.
Cat. No. 206C, Extra s.s. mortar with insulated cup. (Pestle not included)
Cat. No. 206PP138, Polypropylene ball, 1 3/8 inch dia.
Cat. No. 206PP178, Polypropylene ball, 1 7/8 inch dia.
Cat. No. 206SS138, Stainless steel ball, 1 3/8 inch dia.
Cat. No. 206SS178, Stainless steel ball, 1 7/8 inch dia.
Microplates and sealing mats from Porvair Sciences.
Cat. No. 219030
2 ml Deep well Microplate, 50 plates per case
Cat. No. 219004
Sealing Mats, (fits 219030), 50 mats per case
A low cost, disposable, tissue disperser for up to 100 mg samples of soft tissue (e.g., liver, brain and muscle). The Dueling Syringes™ tissue disperser is a significant improvement over the classic "syringe-needle-syringe" method of tissue dispersion. The needle is replaced with an embedded 500 micron stainless steel screen inside a 1 ml polycarbonate syringe. Manual passage of the sample back and forth through the screen is fast, gentle and efficient. Sold as a pack of five pairs of syringes.
Ideal for a one step preparation of cell lysate from most fruits and vegetables. Suitable tissues include tubers, squash, leafy tissues, fruits and pods. One of the few methods that do not require added liquid to obtain a cell free extract. Consequently, the highly concentrated proteins and biochemicals in the homogenate optimize down-stream purification or analysis steps. Not suitable for extracting animal tissue.
This classic tool has two applications in the molecular biology area: 1) Preparing large amounts tissue (100g - >1 kg) for subsequent fast and complete cell lysis using a beadbeater, ultrasonicator, rotor-stator machine or high shear press and 2) recovering large quanties of viable single cells following incubation of the dispersed tissue with proteolytic enzymes that digest extracellular matrix.
This Grinding Mill cuts soft animal or plant tissue and some crushable 'dry' materials like some seeds and leaves. This attachment is powered by our BioMixer hand-held homogenizer.
The Jiffy Mixer is specially designed to stir viscous solutions.
Cat. No. LM, Jiffy Mixer
BioSpec is your source for LabTie™ Bead Loaders. The highly versitile dispenser, custom fit to your application, can quickly and accurately dispense beads, powders, seeds and irregular small partricles into a variety of industry standard plates, tubes, vials, or trays. This gravity-type loader can dispense a wide variety of sizes, shapes, densities, amounts, and volumes.
A variety of LabTie dispensers are offered below and custom dispensers are available to fit your specific needs. Please select the Specifications Tab below to find the appropriate part number for your application. Then highlight this catalog number in the drop-down box below and add the item to your cart.
The leaf tissue punch produces a single 1/4 inch diameter disc. The punch holds a standard snap-top or screw-top microvial in position to receive the sample without further manipulation.
The Lever Tissue Press is a top-of-the-line stainless steel garlic press improved by the addition of a silicone-rubber gasket on the lever press piston.The press efficiently macerates or mechanically disaggregates 5 to 50 grams of fresh, soft plant or animal tissue. By 'soft' we mean nonfibrous tissue. Acceptible examples are muscle, brain, liver, plant fruits, some plant roots and tubers. An extra "can" is included to facilitate processing of multiple samples.
1 1/2' rubber roller, for hand pressing mats onto microplates. Much easier than using your fingers but it is limited to low volume applications.